Most Common Blomberg Appliance Error Codes

Below are some of the most common Blomberg error codes to help you quickly identify what may be wrong with your washer, dryer, dishwasher, oven/stove, or refrigerator. These codes often point to issues like draining problems, overheating, sensor failures, or door-lock faults—making troubleshooting much easier.

Blomberg Washing Machine Error Codes

W01 — Door Lock Fault: The washer can’t lock the door securely. Make sure the door is fully closed and nothing is blocking the latch.
W02 — Water Inlet Problem: The unit isn’t filling with water at the correct speed. Check the supply hose for kinks/blockages and confirm the tap is fully open.
W03 — Drainage Issue: The washer isn’t draining properly. Inspect the drain hose and clean the pump filter if it’s clogged.
W04 — Oversudsing Detected: Too much foam is present, usually from excess detergent. Reduce detergent and use the recommended amount for the load size.
W05 — Imbalance Detected: The load is uneven, causing strong vibration. Redistribute the laundry and restart the cycle.
W06 — Motor Overheating: The motor temperature is too high. Let the washer cool down before running another cycle.
W07 — Spin Cycle Error: The washer can’t spin correctly, often due to imbalance or a motor-related issue. Rebalance the load and try again.
W08 — Water Temperature Sensor Fault: The temperature sensor isn’t working correctly. Check wiring if accessible or contact a technician.
W09 — Control Panel Malfunction: The controls are unresponsive or behaving abnormally. Try resetting the washer and inspect the panel for visible damage.

Blomberg Dishwasher Error Codes

E1 — Water Leakage Detected: A leak has been detected. Check hoses, seals, and the drain pump area for moisture.
E2 — Overflow Detected: The dishwasher senses overflow. Inspect the drain hose for kinks/clogs and ensure the float switch moves freely.
E3 — Water Heating Fault: Water isn’t heating to the required temperature. Possible causes include a failed heater or thermostat.
E4 — Water Filling Fault: The dishwasher can’t fill properly. Check the inlet valve, inlet hose, and water supply.
E5 — Water Drain Fault: The unit can’t drain. Inspect the drain pump, hose, and filters for blockages.
E6 — Turbidity Sensor Fault: The sensor that detects water clarity isn’t reading correctly. Cleaning or replacement may be needed.
E7 — Flow Meter Fault: The water flow meter is malfunctioning. Check for internal blockages or a defective meter.
E8 — Detergent Dispenser Fault: The dispenser isn’t opening or working properly. Ensure it closes correctly and isn’t obstructed.
E9 — Softener System Fault: The softener system isn’t operating normally. Refill the salt compartment and check for clogs.
E10 — Water Intake Time Exceeded: Filling took too long. Verify water pressure and check the inlet hose for restrictions.

Blomberg Oven and Stove Error Codes

E1 — Oven Temperature Sensor Fault: The temperature sensor may be defective. Check connections and replace if needed.
E2 — Oven Overheating: The oven detects unsafe temperatures. Ensure proper ventilation and inspect the thermostat.
E3 — Door Lock Error: The door lock system isn’t locking or sensing closure (often during self-clean). Check the latch for obstruction.
E4 — Control Panel Fault: The interface isn’t responding. Ensure it’s clean/dry and check for loose connections.
E5 — Heating Element Fault: One or more heating elements aren’t working correctly. Look for damage and confirm connections.
E6 — Fan Motor Error: The convection fan motor isn’t working properly. Check for blockage and confirm it’s receiving power.
E7 — Ignition Fault (gas ovens): Ignition is failing. Verify gas supply, igniter condition, and burner ports for debris.
E8 — Cooktop Sensor Error: A cooktop sensor isn’t detecting correctly. Clean the area and remove any obstruction.
E9 — Self-Cleaning Error: A problem occurred during self-clean. Check door seal condition and latch operation.
E10 — Timer Function Fault: The timer/clock isn’t functioning as expected. Reset it or check the related electronics.

Blomberg Dryer Error Codes

F01 — Motor Fault: The motor isn’t running correctly. Check for obstruction and ensure connections are secure.
F02 — Sensor Fault: A moisture or temperature sensor issue is detected. Clean the sensors and check wiring/connections.
F03 — Heating Element Fault: The dryer isn’t heating properly. Inspect the element and replace if damaged.
F04 — Door Lock Fault: The dryer can’t lock or detect the closed door position. Clear the latch and close the door firmly.
F05 — Exhaust Duct Blockage: Airflow is restricted due to duct blockage. Clean the duct and remove lint buildup.
F06 — Overheating Issue: Temperature is too high, often from blocked airflow or a faulty thermostat. Clean filters and check ventilation.
F07 — Control Panel Fault: The interface is unresponsive or malfunctioning. Keep it clean/dry and check for visible issues.
F08 — Drum Rotation Issue: The drum isn’t turning freely. Look for items stuck inside or mechanical obstruction.
F09 — Condenser Sensor Fault: The condenser sensor isn’t reading correctly. Clean the condenser unit and check sensor connections.
F10 — Water Tank Full: The condenser dryer’s tank is full. Empty it regularly to prevent this error.

Blomberg Refrigerator Error Codes

R01 — Temperature Sensor Fault: The internal sensor is reading incorrectly. Check for ice buildup or obstruction near the sensor.
R02 — Door Seal Leak: The door gasket may be worn or damaged, causing air leaks. Inspect and replace if needed.
R03 — Defrost Cycle Error: Defrost isn’t working properly. Remove excess frost and check the defrost timer/heater.
R04 — Cooling Fan Malfunction: The internal fan isn’t circulating air correctly. Inspect for ice or blockage and verify power.
R05 — Compressor Overload: The compressor is overheating or drawing too much power. This may require service or replacement.
R06 — Ice Maker Error: Ice production/dispensing issues (if equipped). Check the water line and clear any blockages.
R07 — Water Dispenser Fault: The dispenser isn’t working properly. Inspect water supply and replace filters if needed.
R08 — Control Board Communication Error: The control board isn’t communicating with components. Try a reset or get a professional diagnosis.
R09 — Humidity Sensor Malfunction: The humidity sensor isn’t detecting moisture correctly, affecting produce freshness. Check for ice or obstruction.
R10 — Door Open Warning: The unit detects an open door for too long. Ensure the door closes fully and sensors are working.